Welcome to QTEC-TECHNOLOGY.com
Logging to website


Please wait

close
 
{{products.length}}
  • {{data.name}}
  • {{data.name}}
 
{{products.length}}
  • {{data.name}}
  • {{data.name}}
You are here:




Product Result




recent products

  • 2000363

    100x25x13mm AL/OX COMBINATIONBENCH STONE

    BRAND : KENNEDY

    PART NO : KEN2551050K

    Combination Bench Stone - Aluminium Oxide Bench Stones. A comprehensive range of bench stones and sharpening stones to cover a wide variety of sharpening and honing applications. Most of the shapes and sizes are available in fine, medium and coarse grades. Available in aluminium oxide or silicon carbide, all stones can be used wet or dry to produce sharp cutting edges or to remove burrs. Aluminium Oxide: Man-made abrasive which is extremely tough enabling high speed penetration of high tensile materials without causing excessive fracturing. This resistance to fracturing makes it a versatile material suitable for general sharpening and honing applications. Combination Aluminium Oxide For workshop use. Ideal for sharpening chisels, plain iron and virtually any metallic implements.

    More Info

    price : 223.00 Baht / EA

    Stock
    Location QTY Lead time (Days)
    Local Thailand 111 7
    International 109 25
    add to cart
  • 2000389

    100x13mm 3SQ. AL/OX MEDIUMSHARPENING STONE

    BRAND : KENNEDY

    PART NO : KEN2552010K

    Three Square Abrasive Sharpening Stones - Aluminium Oxide A range of tough general-purpose Aluminium Oxide 3SQ sharpening stones able to give keen, even cutting edges on all straight edge cutting tools. Consistent and uniform cutting edges ensure fast cutting and longer tool life.

    More Info

    price : 185.00 Baht / EA

    Stock
    Location QTY Lead time (Days)
    Local Thailand 4 7
    International 3 25
    add to cart
  • 2000649

    12x20mm CYL. CARBIDE ENDCUT BURR CUT 9

    BRAND : KENNEDY

    PART NO : KEN2100280K

    Carbide Burrs - Cylindrical-End Cutting Cylindrical-End Cutting. All sizes are nominal. Sizes marked * are 3mm shank, all others are 6mm shank. Cut Numbers: Cut 3 - Rapid Cut For use on softer non-ferrous and plastic materials, i.e. aluminium, fibreglass, plastics, hard rubber and zinc alloy. Cut 9 - Chipbreaker Chipbreaker fast stock removal for improved control and reduced chips for use on hard materials, i.e. steel alloy 50RC, 60RC, carbon and cast iron. Suitable for deburring and polishing of cast iron, cast steel, carbon steel, alloy steel and stainless steel etc. up to HRC65 hardness. Please note: Workpiece and tools should always be steady and well supported. Carbide burrs are not suitable for 'milling' large amounts of material, they are for light stock removal at high rpm's 'LOW FEED - HIGH SPEED'. Always ensure that at least 70% of the shank length is clamped by the collet or chuck of the tool being used. Always ensure that the tool is rated to the recommended operating speed of the burr.

    More Info

    price : 1,193.00 Baht / EA

    Stock
    Location QTY Lead time (Days)
    Local Thailand 7 7
    International 7 25
    add to cart
  • 2001036

    125x22mm F/GLASS AL/OX FLAP DISC P120

    BRAND : YORK

    PART NO : YRK2209650K

    Conical Flap Discs, Aluminium Oxide - Fibre Backed Conical flap discs are a high performance alternative to sanding discs where surface finish is important. On light gauge sheet metal, the overlapped abrasive strips slowly wear away revealing fresh abrasive. Features and Benefits • The overlap design reduces clogging and ensures the disc always cuts effectively and • Provides a consistent finish throughout disc life • No backing pads needed Notes • Safe to use at 80m/s on any grinder Standards EN12413

    More Info

    price : 79.00 Baht / EA

    Stock
    Location QTY Lead time (Days)
    Local Thailand 2229 7
    International 2211 25
    add to cart
  • 2001037

    180x22mm F/GLASS AL/OX FLAP DISC P36

    BRAND : YORK

    PART NO : YRK2209710K

    Conical Flap Discs, Aluminium Oxide - Fibre Backed Conical flap discs are a high performance alternative to sanding discs where surface finish is important. On light gauge sheet metal, the overlapped abrasive strips slowly wear away revealing fresh abrasive. Features and Benefits • The overlap design reduces clogging and ensures the disc always cuts effectively and • Provides a consistent finish throughout disc life • No backing pads needed Notes • Safe to use at 80m/s on any grinder Standards EN12413

    More Info

    price : 147.00 Baht / EA

    Stock
    Location QTY Lead time (Days)
    Local Thailand 1027 7
    International 1027 25
    add to cart